7 Tips for Installing Solid Hardwood Flooring

Hardwood Flooring

One of the best ways to increase a home’s value is by updating the flooring. You can hardly go wrong with hardwood flooring despite the ever-changing trends. As long as you use the right tools, have adequate knowledge and patience, the installation of the floor wouldn’t be a much bothersome job. When using solid hardwood flooring, leave the wood in open boxes for at least a few weeks before installing the hardwood flooring. The wood needs to acclimatize to your home’s temperature and humidity to prevent cupping or shrinking post installation. Advice for installing Solid Hardwood in 7 Steps Removing the Baseboard Before installing solid hardwood flooring, the baseboard needs to be removed. While people may recommend undercutting the base, it may make you lose height of the baseboard. You may want to replace or upgrade your baseboard when installing new hardwood flooring. To ensure you remove the base cleanly score the top edge of the base with a utility knife. To pull the baseboard away from the wall, use a small trim pry bar. If you plan to use the baseboard again, set it aside on the site or dispose if you plan to replace it post installation of the hardwood floor. Preparing the subfloor It may take more time to prepare the subfloor that the actual installation of the hardwood flooring. When removing carpet, you can simply use pliers to pull up the carpet and then remove tack strips and underlayment. When removing other types of flooring, the work may be more time consuming. Vinyl flooring is the most difficult to remove Hardwood flooring may be installed on top of particle boards, however most manufacturers wouldn’t recommend that as the staples and nails won’t hold on well. You may simply remove the vinyl layer with a scraper and heat gun the surface flat in case of vinyl over OSB or ply underlayment. Final Subfloor Preparation It is important to check for remaining nails or uneven floor after removing the flooring before you begin installing the new flooring. You can use a steel dustpan or a scraper to run it across the floor at a sharp angle to figure out what needs to be fixed. You can sand the edges to ensure that the edges of the subfloor are flat. With this done, the installation will get much easier. Laying Moisture Barrier/ Paper To keep things from sliding around, it is best that you use a paper underlay as a moisture barrier. You can check with the hardwood supplier as to what they’d recommend according to local climate. Racking the Floor While trends change, the fundamentals remain the same. Here is what to follow when laying out the floor: Ensure that the joints do not come too close together. The joints at the same location need to be at least two rows apart instead of one row apart as seen in older homes. Start laying out or racking before you start stapling or nailing. When racking, use both the table saw or miter saw and ensure that you have a clean cutting area to avoid sawdust under every board post cutting. Installing and Layout the Hardwood Use a pneumatic tool for nailing, as it is one of the most important steps of the installation. You can rent the equipment if you don’t have it already. Manual nailing is also a choice with professionals these days. Solid hardwood has some natural expansion and thus you must leave space for that while nailing. The baseboard will cover the extra-allotted space. This is essential to avoid floor cupping at a later stage due to expansion. Baseboard Installation and Touch ups Once the installation is done, half the work is still left. You need to re-install the baseboard and ensure that any nailing marks you may have made on the wall or the floor is cleaned. These touch ups add to the wow factor of your flooring. This done, installing solid hardwood flooring will now be a breeze.  

The post 7 Tips for Installing Solid Hardwood Flooring appeared first on Stumpblog.

This content was originally published here.

Trending Flooring Types used in Building and Renovation

Hardwood Flooring

Have you planned to get new flooring installed in your home? Then you might be looking for flooring types which are in trend these days. Choosing the right flooring is a critical decision to be taken. It can add value to your property and can make your place look appealing. You can find a variety of trendy flooring types in the market but important is to select the one which satisfies your needs and goes with the interior of your house. Also, if necessary you should take the advice of a flooring expert. Go with the following trending flooring types to have a clear knowledge about them. Also, it will become easy for you then to select the right flooring for you. 1. Ceramic or Porcelain Tile Having tiles in the bathroom is the best option, but many people like to have them in the kitchen, dining area, or laundry room. Tile can be considered as the most versatile flooring as there are certain tiles having the design of hardwood and durability of ceramic. Porcelain and glazed ceramic tiles require very little maintenance and are most durable. The tile needs not to be expensive. It only requires the right person for the installation process. 2. Hardwood and Bamboo – When it comes to hardwood flooring, nothing can beat its aesthetic appeal. Hardwood is a fantastic option for living areas and kitchen in some cases. But it should not be installed in areas which get wet frequently like bathroom, mudroom, and laundry room. The plus point about hardwood flooring is that it can go with almost all types of interior decor. Bamboo flooring is similar to hardwood in terms of cost, installation, performance, and maintenance. Hardwood flooring demands extra care because if not kept clean, it gets scratches easily. 3. Carpet – No doubt, carpet is an attractive option and is available in many colors and styles. Also, its installation is very easy and quick. Carpets are very warm, quiet, and soft, and it is the reason that most homeowners like to have it in their bedrooms. Remember carpets are prone to damage from pets and stains. So be cautious while selecting a carpet if you have pets and kids at home. 4. Laminate – Laminate flooring is a low-cost alternative. It is made up of resin and wood pulp and can give the look of real wood. It is quick and easy to install and is created for the click-together floating-floor installation. It can be glued on the floor, but is not recommended. 5. Vinyl and Linoleum – Both vinyl and linoleum belongs to resilient flooring and are almost similar. The main difference between them is that vinyl is plastic, usually acrylic, PVC, and the same polymer, whereas Linoleum is made of natural materials like cork and jute. They come in the form of tiles, sheets, and planks and are easy to install. They are available in a wide range of styles and colors. Furthermore, they are moisture-resistant, highly durable, and are a good option for high-traffic areas.  

The post Trending Flooring Types used in Building and Renovation appeared first on Stumpblog.

This content was originally published here.

4 Things to Consider Before Buying New Floors

Hardwood Flooring

Are you
thinking about replacing your floors? Here are four things you need to consider
before you invest in new floors.

One way to give your
home a fresh look is to buy new floors. Quality flooring can change the entire
ambiance and feel of a room, increase your home’s curb appeal, and add a touch
of style.

The problem is that
there are way too many options to choose from.

Most stores nowadays
sell bamboo flooring, laminate flooring, hardwood flooring, and ceramic tiles —
just to mention a few. Plus, you need to consider its color, dimensions,
durability, price, and other factors.

A little research can
make everything a lot easier. Here’s what you should know about buying a new
floor so you can make the right decision!

Consider How the Room Will Be Used

The first step to buying
new flooring is to consider how the room will be used. A cheap wood floor, for
example, might be great for your basement or attic, but not for your bedroom or
living room.

If the new floor will be
installed in a bathroom, basement, or other high-moisture areas, go for vinyl
tile, porcelain tile, or ceramic. Concrete flooring is a good choice too.

Do you have children or
pets? In this case, it’s important to opt for quality flooring that resists
wear and tear.

Think plank vinyl
flooring, laminate, porcelain or ceramic tile. Shop around for discount vinyl plank
 and other models
to get a good deal.

Choose the Best Type of Flooring

There are literally
dozens of flooring materials on the market. Choosing one depends on your
budget, preferences, and individual needs. Popular options include:

  • Luxury vinyl tile
  • Rigid core flooring
  • Engineered wood flooring
  • Ceramic tile flooring
  • Glazed vitrified tiles
  • Marble flooring
  • Stone flooring
  • Limestone flooring
  • Granite flooring
  • Hardwood flooring
  • Laminate wood flooring

Let’s say you need a new
floor for your kitchen. In this case, it’s recommended to use waterproof
materials, such as wood, linoleum, or natural stone.

The possibilities are
endless when it comes to buying new floors for your living room. Some
homeowners love the classic feel of carpeting, while others prefer the
durability and timeless style of hardwood.

Request a Sample

Once you’ve decided on a
type of flooring, ask for a sample. Whether you shop online or at a physical
store, sellers should be able to fulfill your request.

It’s one thing to see
your flooring choice in photos and another thing to see how it looks in your
kitchen or bedroom. Consider the lighting of the room as well as the overall

Do the Math

While the price per
square foot matters, there are plenty of other factors to consider when buying
new floors.

First of all, some types
of flooring are easier and cheaper to install than others. Secondly, certain
materials either require extensive maintenance or need to be replaced every few

Hardwood flooring, for example, can last a lifetime. Although it
comes with a higher price tag than most materials, you’ll save money in the
long run. A more affordable alternative is engineered wood flooring.

Terracotta tile, on the
other hand, needs to be sealed regularly. Otherwise, it may become stained. If
you choose linoleum floors, be prepared to refinish them every two years or so.

Change the Look and Feel of Your Home with New Floors

Shopping for new floors
can be excruciating, especially if you’ve never done it before. You may not
know what to look for, how to choose the right materials, and where to find a
good deal.

Take the time to
research your options. Read about the different materials, how long they last,
and whether or not they require maintenance.

Not sure where to start?
Perhaps you need some inspiration? Browse our DIY section for tips and tricks
that will make everything a lot easier!

The post 4 Things to Consider Before Buying New Floors appeared first on Useful DIY Projects.

This content was originally published here.

Best Craftsman Miter Saw – Buyer’s Guide for 2019

Hardwood Flooring

Craftsman tools have been a powerhouse for the last 90 years due to their wide product line and dependability. Their miter saws also fulfill these promises to consumers. Craftsman was sold to a new company in 2017, making changes to their product line and providing new miter saw offerings. Some of these older models are still available today alongside Craftsman’s new line.

To help you navigate their products, we have chosen the best Craftsman miter saws available on the market and where to find all the accessories to make your sawing experience seamless. Are you looking for the best miter saw overall? If so, check out The Best Miter Saw – Complete Buyers Guide & Reviews.

Quick Look at Our Top Picks:

Image Product Price
Craftsman 10″ Single Bevel Sliding Compound Miter Saw (21237)
  • $278.01
Craftsman 7-1/4” Single Bevel Sliding Compound Miter Saw (CMCS714M1)
  • $289.00
DOIT 15-Amp 10-Inch Single-Bevel Compound Miter Saw with Laser Guide
  • $99.99

Last update on 2019-09-12 / Affiliate links / Images from Amazon Product Advertising API

Best Craftsman Miter Saws

The first saw we recommend is part of the old Craftsman line, and you won’t find it on their website. We believe it’s a great quality saw that you can still find through other online retailers. Our other two recommendations are part of the new product line, which can be found on their website, in big box stores, and on other online marketplaces.

Craftsman 10″ Single Bevel Sliding Compound Miter Saw (21237)

Last update on 2019-09-12 / Affiliate links / Images from Amazon Product Advertising API

This saw works for almost everyone, and that’s why we like it. Whether you are planning on using this around your home or on a job site, its versatility and cutting power make it a great choice for a variety of jobs. Professionals may get the most out of it as you can take it from job to job and perform many types of cuts. At a reasonable price point, this saw satisfies the needs of anyone who needs a sliding compound miter saw.

What We Like

  • Lightweight (31.8 lbs.) and portable for easy use from job site to job site
  • Capable of clean cuts on both soft and hard wood
  • Quiet saw compared to most in its class

What We Don’t

  • Laser location makes it almost impossible to see the line in sunlight
  • Dust sprays everywhere due to poor dust collection
  • Plastic carrying handle has been known to break

DOIT 15-Amp 10-Inch Single-Bevel Compound Miter Saw with Laser Guide

Last update on 2019-09-12 / Affiliate links / Images from Amazon Product Advertising API

One of the newer Craftsman offerings, you can find this saw online or at many big box stores and local hardware stores. This small and compact saw is our recommendation for DIY projects, such as framing, molding, and furniture building.

It comes at an affordable price for small projects and those who don’t use their saw frequently. While it may be less expensive and for smaller jobs, its accuracy and performance do not suffer. You will find that this saw delivers on quality and precision.

What We Like

  • This is a folding miter saw, great for flat and small storage
  • Lightweight design (28 lbs.) makes portability optimal
  • Electric brake stops your cuts for quickness and efficiency
  • Laser guide improves efficiency in cutting accuracy

What We Don’t

  • Poor dust collection like most miter saws
  • Plastic saw base could use improvements in security and stability
  • Angle gauges are stickers rather than metal plates with potential to rub or scratch off

Craftsman 7-1/4” Single Bevel Sliding Compound Miter Saw (CMCS714M1)

Last update on 2019-09-12 / Affiliate links / Images from Amazon Product Advertising API

Don’t be fooled by the small blade size, this saw packs a punch for its size. At an affordable price point, this saw is best for those who work on smaller projects. It is a great addition to your home power tool collection for its power, accuracy, and easy storage.

Hardwood flooring, baseboards, trim, and 2-dimensional lumber are just a few of the materials this saw can cut with no problem. With a quiet motor and smooth cutting, we are impressed by the high performance with a smaller blade compared to the competition. We recommend this saw for all your DIY projects!

What We Like

  • Incredibly lightweight (21.8 lbs.) design with carrying handles makes it very easy to transport and store
  • Battery-operated machine allows for working in powerless locations
  • Battery lasts up to two hours without recharging and can recharge in 60 minutes or less
  • LED light aids in accuracy and visibility of cut line

What We Don’t

  • Poor dust collection gets dust caught in sliding rails and can limit saw movement
  • Unit only comes with one battery, making a full charge necessary when remote
What Should You Know About Craftsman Miter Saw Stands and Parts?

Once you found your miter saw, you’ll need something to put it on. If you do not have a work table with lots of space for long or large pieces of wood, it may be difficult to use your saw effectively. Using a miter saw stand can solve these problems. With an ability to set up in any space, you’ll have enough room and can conveniently move it to your desired work location. Are you interested in buying the best miter saw stand? If so check out The Best Miter Saw Stand.

Craftsman miter saw stands pair well with your saw for sturdy and easy use. They offer lightweight stands with universal brackets for almost any saw and more advanced models with outlet connectors, wheels for transport, and increased stability. Make sure you look for a stand that can support the weight of your saw and is easy to transport.

Finding Craftsman miter saw parts doesn’t have to be difficult either. When things break down after extended use or accidents happen, we want to know that our saw can be repaired with the correct parts. With the change in ownership from Sears to Stanley Black and Decker, you might be on a chase for your model’s part.

If you need new Craftsman saw parts, you can contact them directly. You can also find a variety through online marketplaces. Check for correct dimensions for parts that are not made by Craftsman to ensure proper fit. craftsman miter saw

How Should You Navigate a Craftsman Miter Saw Manual?

For many things we buy, we take one look at the manual and throw it away. For a miter saw, it is important that you take the time to acquaint yourself with the tool for safety and proper use.

Miter saws usually require minimal set up, but need to have all parts attached and often need to have the alignment adjusted. Using your manual, it will guide you through these steps. Craftsman miter saw manuals are easy to follow with clear descriptions and photos. Consumers regard them as generally helpful and easy to use.

They are also helpful to refer back to after initial set up when changes need to be made or problems arise with your saw.

Final Recommendation

Last update on 2019-09-12 / Affiliate links / Images from Amazon Product Advertising API

While it may not be part of the new product line, our favorite Craftsman miter saw is the 10″ Single Bevel Sliding Compound Miter Saw (21237). Its versatility and usefulness for beginners, homeowners, and professionals had us sold. You will be able to complete a wide range of jobs and complete many types of cuts with this easy to use and affordable saw! Are you looking for the best Ryobi or DeWalt miter saw? If so, check out The Best DeWalt Table Saw, DWS709 vs DWS779: Head to Head with Two of DeWalt’s Best Miter Saws, and the Best Ryobi Miter Saw 2019: Which One Should You Buy?

The post Best Craftsman Miter Saw – Buyer’s Guide for 2019 appeared first on The Saw Guy – Saw Reviews and DIY Projects.

This content was originally published here.

What Are the Best Types of Wood for Hardwood Flooring? | Embrace Home Loans

Hardwood Flooring

Back in the 1980’s, a whole new generation of homeowners experienced the thrill and beauty of solid hardwood floors as they stripped away the orange and green wall-to-wall shag carpeting which had been so popular in the 1970’s. Hardwood floors are resilient and long-lasting. They don’t peel or crack and best of all — unlike that old shag — they don’t get moldy. Real hardwood floors are easy to refinish and restore and are sure to add value to any home.

Hardwood flooring is typically 3/4″ thick, with each plank a single solid piece. Hardwoods can contract and expand depending upon the climate and the plank width. Hardwoods are generally more expensive than engineered flooring and require the addition of a sub-floor, as well as several coats of protective finish. The most popular hardwoods are those that are readily available.

Choosing hardwood flooring

Aside from plank width, color, and grain, when it comes to choosing a type of hardwood flooring the most important thing to consider is strength and durability.

Hardwoods like oak and maple derive from deciduous trees, while softwoods come from conifers. Softwoods like pine, poplar, walnut, and spruce are better used for furniture and cabinetry. You may also choose form tropical hardwoods such as mahogany, teak, and rosewood. These hardwoods are are not native to North America and can be considerably more expensive as a result.

Top 10 hardwoods, according to the American Hardwood Information Center

Hardwood re-engineered

Unlike solid hardwood floors which are milled from a single piece of timber, engineered wood flooring planks are made up of two layers — the lamella, or top surface, over a supporting core layer. The core can be made of a “wood ply” which uses multiple thin plies of wood glued together, “finger core” made of small pieces of milled timber that run perpendicular to the top layer, or fiberboard.

Engineered floors maintain stability by running each layer at a 90 degree angle to the layer above. A true engineered hardwood floor uses sawn wood for its surface layer, not veneer. No wood composite or plastic is used in the manufacturing process. Engineered hardwood can be installed over concrete and doesn’t generally require a separate sub-floor.

Engineered flooring gives you more choices

When shopping for an engineered floor you’ll find many wood veneers options, from standard oak to exotic Brazilian cherry. Oak, maple, walnut, and mahogany are all considered traditional, whereas beach and pine are lighter and more suitable for a contemporary space. You’ll have a variety of choices when it comes to plank width as well — wide or narrow, edging, beveled or square, as well as the type of installation system. Perhaps the best known of these is “tongue-and-groove.” Each plank having one side and one end grooved so that they fit tightly with adjoining planks.

Unlike tongue-and-groove which must be glued down, a number of manufacturers have developed patented “click” systems of installation. While similar to tongue-and-groove, instead of fitting directly into the groove, the board must be angled or “tapped” in to make the curved or barbed tongue fit into the adjoining modified groove. Other floor connection systems are available that allow for the incorporation of other materials including metal and rubber. Parquet style floors use a glue down method. Small pieces of wood are affixed to glue applied directly to the concrete surface and then tamped down with a rubber mallet.

Engineered wood flooring has made it possible for a generation of DIY homeowners to upgrade their homes. A word of caution, though — the top layer of your engineered hardwood floor is much thinner than a solid hardwood floor and should not be sanded often. A true solid hardwood floor will last for generations. Engineered hardwood flooring? It remains to be seen.

The Bottom Line

Whether you choose real hardwood or engineered flooring, there is wide range of high quality products available that will enhance both the beauty and value of your home.

This content was originally published here.

Amon Carter Museum of American Art Reopens With New Exhibits

Hardwood Flooring

It’s light, it’s bright and on September 14, a refreshed Amon Carter Museum of American Art will reopen to the public after a year-long renovation.

“For the last year, the museum has been engaged in what we would refer to as a transformative experience for the Amon Carter,” Andrew J. Walker, the museum’s Executive Director, said. “The public spaces of the Amon Carter over the last year have been completely reimagined.”

The reimagining of Fort Worth museum began in October 2018 with an upgrade and expansion of its photography vaults. The visible changes to the public areas come after a three-month closure. Hardwood flooring, LED lighting mimicking daylight while preserving delicate artwork, new sightlines and a new gallery layout showcase the museum’s newly reinstalled collection of American art. The museum’s front entrance now features a ramp system, increasing accessibility to the main campus.

[[560187471, C]]

The museum’s curators have used the renovation as an opportunity to re-evaluate the collection and create galleries offering fresh perspective on American creativity. Thematically focused galleries include American Roots, Opulence and the Everyday, America as Landscape, Legacy Galleries: Remington and Russell, Modern America, Make It New and Works on Paper.

The Works on Paper gallery will highlight the nearly 10,000 works on paper in the museum’s collection. The gallery currently features “Seeing in Detail: Scott and Stuart Gentling’s Birds of Texas,” an exhibition featuring 23 original watercolors of native Texas birds by the Gentling brothers. The museum also announced the establishment of the Gentling Study Center. The center will support the acquisition, research and conservation of the Fort Worth artists’ works.

[[560187561, L,300,390]]

The first major touring exhibition in the newly renovated space is “Gordon Parks: The New Tide, Early Work 1940 – 1950.” Organized by the National Gallery of Art, Washington and in collaboration with The Gordon Parks Foundation, the exhibition, on view through December 29, chronicles Park’s formative years. “When the show starts, he is a fledgling self-taught photographer,” John Rohrbach, Senior Curator of Photographs, said.

The exhibition explores Parks’ evolution as a photographer through 150 photographs as well as magazines, newspapers, pamphlets and books. From working as a portrait and fashion photographer in Saint Paul and Minneapolis to becoming the first African American staff photographer at Life magazine, Parks used his art to lift the story and the contributions of the African American community.

“This is a story about not only achievement, not only a story of roots, but a story of community. We all work with others; we rely on the gifts of others to us to find our own way. And what Parks did was take those connections and strive to better himself and do something more, not only for himself but also for the African American community,” Rohrbach said.

The renovation expanded and improved the museum’s special exhibition space. Walls that do not quite reach to the ceiling are module units that can be reconfigured to meet the program’s needs. “It allows us to host more ambitious special exhibitions and it also allows us to host more than one rotating show at the same time,” Brett Abbott, Director of Collections and Exhibitions, said.

The exhibition to most benefit from this expansion is “Set in Motion: Camille Utterback and Art That Moves,” now on view through December 8. “This is a show that wasn’t possible before this renovation,” Kristen Gaylord, Assistant Curator of Photographs, said. Before the renovation the video space was not large enough to house Utterback’s digital work, “Untitled 5.”

[[560187581, C]]

“Untitled 5” is an interactive work with visitors stepping into a rectangle illuminated on the floor. The visitor’s movements through the rectangle is tracked by a camera overhead, run through an algorithm and then translated into markings on a digital painting. Visitors can watch how their movements push against the artists’ brush strokes. The piece constantly changes as visitors walk, skip, twirl and wave through the space. “Camille Utterback really believes technology is a tool that can be used in many different ways and her way of using it is to try to emphasize our physical experience,” Gaylord said.

This interactive piece is paired with art by women who also experiment with the idea of bodily movement and motion in their work.

The museum commissioned Justin Favela, a Mexican-and Guatemalan-American artist, to create a large-scale work to fill the first-floor gallery connecting the museum’s original 1961 building to the 2001 extension. Maggie Adler, the museum’s Curator of Paintings and Sculpture, introduced the space to the artist known for reinterpreting historical artworks employing materials used to make piñatas.

“When Maggie approached me and said, ‘Alright, this is the space. What do you want to do with it?’ I just said, ‘I want to cover the entire thing in paper. I don’t want any negative space,'” Favela said. Thanks to a new paper supplier, this creation will be Favela’s most colorful work yet, using 43 different colors of tissue paper.

[[560187641, C]]

Favela started looking at the museum’s collection for inspiration six months ago. This immersive work called “Puente Nuevo” is inspired by color lithographs depicting scenes of rural and urban Mexico by Casimiro Castro, a 19th century Mexican printer. “I’m really excited to pay homage to a Mexican artist that is part of this collection that maybe wasn’t looked at in many years,” Favela said.

CLICK HERE to learn more about the Amon Carter Museum of American Art’s Reopening Celebration.

Photo Credit: Amon Cater Museum of American Art
This story uses functionality that may not work in our app. Click here to open the story in your web browser.

This content was originally published here.

An Agent’s Guide to Home Styles, Architecture, and Design

Hardwood Flooring

Home Styles guide for real estate agentsWant to know a secret? As a real estate agent you’re not really selling relationships or trust or negotiation skills. Nope. You’re selling houses, plain and simple. There’s no way around it.

That means if you want to become a hyper local expert, you’d better know the different home styles in your region, state, and farm area. After all, wouldn’t you rather ask your client if they liked the Queen Anne with herringbone floors and Palladian windows they saw yesterday instead of “the old red house with the cool floors?”

Thought so.

If you’re even a little unsure about the common home styles you’re going to be selling in your farm area, check out our cheat sheet of common home styles, window styles, door styles, and flooring styles below.

Cheat Sheet for Common American Home Styles

Although Europeans love to joke about how new and boring American architecture is, in reality we have dozens of influential styles of homes. Since you’re a real estate expert, you should be able to identify each style listed below. If you can’t, read the style and description below then come back to this article in a few days and quiz yourself.

Here are the most common home styles in the United States to get you started:

Craftsman Style Homes

Period: 1900-1930
Commonly found in: California, Seattle, Oregon

With design elements from the British arts and crafts movement of the late 19th century, craftsman style homes became extremely popular in the early 20th century. The characteristic elements of a craftsman style home include a low slung roof, large front porches with a staircase leading up to it, large squared off columns that were usually exposed or decorated with stones or brick, and minimal decorative elements.


An Architecture Cheat Sheet for Real Estate Agents

photo via: Warburg

Period: 1840s-1890s
Commonly found in: Manhattan, Brooklyn, Philadelphia, Boston

Built from the eponymous stone quarried in Connecticut, brownstones were a very popular style of townhouse in many East Coast cities like New York, Brooklyn, Philadelphia, and Boston. When first pulled from the ground, brownstone is actually pink, but settles into a rich dark brown over time.

Many brick townhouses are mistaken for brownstones because of the way they’re painted, but true brownstones were always made from actual brownstone which was a preferred building material because of its softness and ease of working with.


An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1820s-present
Commonly found in: Manhattan, Brooklyn, Philadelphia, Boston, Washington D.C., Baltimore

A rowhouse is a single family home that shares a roofline and one or more walls with a group of other homes on a single block. Frequently built at the same time by the same developer, rowhomes were a very popular style of housing in 19th century American cities due to the cost savings of building multiple homes at once on one plot of land.

While rowhomes generally share many of the same features including window styles and placement, front stoops, and yards, some rowhouses were built with eclectic styles of homes grouped together. When building homes, workers built doorways connecting each rowhome together so they could easily walk from one home to the next to finish construction. These doorways were then sealed when the homes were sold to buyers.

Cape Cod Style Homes

Cape Cod style homePeriod: 1740s-present
Commonly found in: East Coast, Midwest

Cape Cod style homes were very common with early American settlers due to their relative ease of construction and simplicity. They generally feature a single pitched steep roof, front door in center with rows of windows on either side. Shingle or clapboard siding, sparse and minimal decorative elements. Dormer windows were common additions to Cape Cod homes.

Ranch Style Homes

An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1920s-present
Commonly found in: West Coast, Everywhere

Ranch style homes were the modernist answer to affordable family living. With only one story and low slung roofs, ranch homes allowed for open-plan layouts and a more laid back, less formal style of living that became popular in the early 20th century modernist movement.

A hallmark of American suburbia, ranch homes became so popular that by the 1950s nine out of 10 new homes built were California ranch homes. Ranging from luxurious and sprawling midcentury modern homes to the most basic starter home, ranch houses were truly versatile and built for American families from every walk of life.

Split Level Homes

split level home stylePeriod: 1950s-present
Commonly found in: West Coast, Everywhere

Split level homes are multi-floor houses with short flights of stairs connecting each level. On the East Coast, split levels almost always have an entryway that opens on to two flights of stairs, one going up to the second level, and another heading down to the first or ground floor. The top floors of a split level home tend to have full height ceilings while lower levels might have lower ceilings.

Midcentury Modern Homes

An Architecture Cheat Sheet for Real Estate Agents

photo via: Halstead

Period: 1940s-1960s
Commonly found in: New Canaan Connecticut, Chicago, Los Angeles, New York

Inspired by high modernist European architects like Le Corbusier and Ludwig Meis van der Rohe, the midcentury modern movement in American houses began in the 1940s and became extremely popular. Common features include minimalist design with no ornamentation, single story construction, large picture windows, flat roofs, and an attempt to blend the natural surroundings into the design of the home. Interiors usually had open layouts with few walls separating the space which allowed rooms to blend into one another.

Bungalow Homes

bungalow home stylePeriod: 1940s-1960s
Commonly found in: California, Oregon, Everywhere

Often borrowing elements from craftsman design, bungalows are relatively small, single story homes. They often have small front porches and double pitched roofs often with small dormer windows.

Want a fun talking point for your clients when you’re showing a bungalow? Tell them that the style and term originated in the word “bengala” which referred to homes built in the style of the Bengal region of India.

Greek Revival Style Homes

An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1820s-present
Commonly found in: Southeast, Middle Atlantic Region

Often called America’s first unique architectural style, Greek Revival homes were inspired by elements of ancient Greek architecture. These frequently include large columns in at the entryway or along the entire front of the home, symmetrical double hung windows, and large front doors with sidelights. Ornamentation is generally very restrained and almost minimal.

Also called the national style, Greek revival homes were very popular in the South, especially for mansions and plantation homes.

Postmodern Style Homes

postmodern home stylePeriod: 1980s-present
Commonly found in: California, Everywhere

The postmodernist movement was a philosophical and artistic movement in the 1980s that questioned traditional modernist ideals and employed irony and pastiche in home design.

Postmodern homes might borrow elements from Spanish, Midcentury modern, or even Victorian elements into one house.

Storybook Style Homes

An Architecture Cheat Sheet for Real Estate Agents

Photo via: Douglas Elliman

Period: 1920s-present
Commonly found in: California, Everywhere

Storybook homes are houses that take design cues from medieval European homes that were popularized by fairy tales and castles. Often incorporating stone and shingled roofs, you can usually tell if you’re looking at a storybook home if it wouldn’t look out of place in a Disney cartoon about knights and princesses.

We recently wrote an article featuring seven excellent examples of storybook homes here.

Contemporary or Ultramodern Style Homes

ultramodern home style

photo: the Agency LA

Period: 1990s-present
Commonly found in: Everywhere

Contemporary homes are homes that follow up-to-the-minute architecture and design trends. That means that a contemporary home built in 1990 will look significantly different from one built in 2017 like the example above.

Some common elements of contemporary or ultramodern homes include walls of glass, open concept layouts, high ceilings, kitchen islands, formal and informal living rooms—and large open kitchens.

Spanish Style Homes

An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1920s-present
Commonly found in: California, Southwest

Inspired by the architecture of Spain, Spanish styled homes generally have low slung roofs, terracotta roof tiles, and white plaster walls. The interiors frequently have tile floors, and arched entryways and windows are common.

Tudor Style Homes

An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1850s-1970s
Commonly found in: East Coast, Midwest

Tudor homes generally have high sloped roofs with multiple pitches, brick or stone construction of facades, chimneys, and the trademark faux exposed timbers set in white stone or stucco. Tudor homes saw a resurgence in popularity in the 1920s, and entire neighborhoods like Forest Hills in Queens are almost entirely Tudor houses.

Victorian Style Homes

Victoria home stylePeriod: 1850s-1920s
Commonly found in: East Coast, Midwest, San Francisco

Based on the Victorian design movement in England, Victorian homes in the United States featured ornate decoration on the outside of the home including steep gabled roofs, bay windows, rounded turrets, and dormer windows.

Colonial Style Homes

An Architecture Cheat Sheet for Real Estate AgentsPeriod: 1700s-1780s
Commonly found in: Northeast, Southeast

Colonial houses are characterized by gently sloped roofs, an entrance door in the middle of the home, with two windows flanking the entrance door. Colonials can also have dormers, sunrooms, or other smaller additions to the sides of the home. They are frequently found in the northeast and southeast, and have been a popular style that is still built to this day.

Federal Style Homes

An Architecture Cheat Sheet for Real Estate Agents

photo: Wikipedia

Period: 1780s-1800s
Commonly found in: Northeast, Southeast

When colonial style homes fell out of favor in the 1780s, federal style homes took their place. Federal style homes are very similar to colonials, except they tend to have more ornamentation, decorative or even round windows, columns, and dual chimneys.

Queen Anne Style Homes

Period: 1880s-1920s
Commonly found in: Northeast, Southeast, California

Queen Anne style homes are a type of Victorian home that is even more ornate than a typical, earlier era Victorian. Queen Annes tend to have features like large rounded turrets, steeped roofs with many pitches, stained glass, finials, ornate shingles, and enclosed rounded porches.

Common Window Styles of American Homes

Now that you’ve got a good grasp of some of the more common house styles in the United States, let’s check out some common window styles.

Dormer Windows

An Architecture Cheat Sheet for Real Estate AgentsA dormer is a small structure with a roof that extends out on the roof of Colonial, Cape Cod, Victorian, or Federal style homes. They generally have double hung windows and were often designed to allow light into lofts or even attic spaces.

Bay Windows

An Architecture Cheat Sheet for Real Estate AgentsBay windows are large, segmented windows that extend out from the wall of a house. Bay Windows generally have three angled window panels, and can sometimes have a built in seating area as in the picture above, or add slightly more floor space to a room.

Bow Windows

Bow windows are very similar to bay windows except instead of having three panels, they often have five or more panels which creates a more curved look. To remember the difference, try and associate a bow window with a bow and arrow and a bay window with three bays.

Double-Hung Windows

An Architecture Cheat Sheet for Real Estate AgentsDouble hung windows are rectangular windows with two panes of glass (called sashes), each of which can be raised or lowered to open either the top or bottom of the window. Multiple double hung windows can be installed in one large opening in order to create one larger window. The picture above shows three double hung windows installed into one opening.

Single-Hung Windows

An Architecture Cheat Sheet for Real Estate AgentsSingle-hung windows are identical to double-hung windows except for the fact that only one window sash slides up and down. In most cases, the movable sash will be the lower one.

Casement Windows

An Architecture Cheat Sheet for Real Estate AgentsUnlike double hung windows which open and close vertically, casement windows are hinged on one side to open horizontally into a room.

Palladian Windows

An Architecture Cheat Sheet for Real Estate AgentsPalladian windows are made up of one long rectangular panel with a rounded top flanked by two shorter rectangular windows with flat tops.


An Architecture Cheat Sheet for Real Estate AgentsSidelights are long, thin, rectangular window panels traditionally installed on both sides of entry doors. In more modern homes, there may be only one sidelight, and instead of paned glass, it will be one large section of glass.

Arched Windows

An Architecture Cheat Sheet for Real Estate AgentsArched windows are rectangular windows with a rounded top. One arched window makes up the center window for a Palladian window.

Picture Windows

An Architecture Cheat Sheet for Real Estate Agents

Photo: The Agency LA

Picture windows are large, rectangular windows that are longer horizontally than vertically. Picture windows are made up of one large piece of glass without any separate panes. Picture windows let in lots of sunlight and great views, but generally do not open. The picture above shows a picture window with a casement window section that opens.

Paned Windows

An Architecture Cheat Sheet for Real Estate AgentsPaned windows are windows that are broken up into smaller square sections by wooden frames. They are designed this way because breaking one pane of glass means you only have to replace that single small pane instead of the whole window. Since glass is much cheaper these days and construction costs higher, many modern windows have faux wooden frames to separate a sheet glass window into panes. The picture above shows a paned casement window.

Common Door Styles of American Homes

While getting familiar with windows is helpful, doors are arguably more important for many homeowners, and something any weekend warrior can handle replacing. That means knowing some basic door styles can only help you as an agent. Here are the most common exterior and interior door styles in America.

French Doors

An Architecture Cheat Sheet for Real Estate AgentsFrench doors, sometimes referred to as dual doors, are sets of two doors that are hinged from the right and left to open in the middle. French doors usually feature paned glass, and were traditionally used indoors to separate common rooms without sacrificing light. Sometimes, French doors are used to open onto a deck, patio, or back garden, but are rarely used as entry doors.

Pocket Doors

A common feature in turn of the century brownstones and mansions, pocket doors are similar to French doors except, they slide on tracks instead of opening on hinges. Each of the two doors in a set of packet doors slides into the wall. This gives the homeowner the choice between totally closing off rooms for privacy, or keeping them totally open without any visible doors at all.

Barn Doors

Popularized on Pinterest and many home renovation shows, barn doors are generally repurposed sliding front doors from barns. While some barn doors have windows, many do not and only feature minimal panels, or even just planks. They are almost always made out of repurposed vintage barn wood, or new wood that has been weathered to look like vintage barn wood. Like pocket doors, barn doors allow homeowners to put furniture very close to them without worrying about the space required to open the door.

Panel Doors

Very common for interior and exterior doors, panel doors are doors with either decorative or structural panels on both sides of the door. While there are many different patterns and sizes of panels for panel doors, most interior doors have only two or three panels. Panel doors are very common in any pre 1950s house style.

Flush Doors

Flush doors on the other hand are most often found in midcentury or contemporary homes. Unlike panel doors, they have one solid plane of wood on either side of the door. They can either be one solid piece of wood, or made with wood veneers on either side of hollow constructed frame.

Dutch Doors

An Architecture Cheat Sheet for Real Estate AgentsDutch doors are almost always found in vintage homes and rarely found in homes built after the 1960s. They have one unique feature that sets them apart from other entry doors. There are two hinged sections of the door rather than just one and each section can be opened or locked independently. Dutch doors are great for pet owners who want a breeze but don’t want their pets to escape.

Interior Design Elements of American Homes

Now that you’ve talked your way inside, it’s time to learn about some of the trickier interior design elements that are common in American homes. While most of these elements will be found in historic homes, you will find them in newer homes as well.

Crown Molding

An Architecture Cheat Sheet for Real Estate AgentsCrown molding is the decorative trim at the corner where the top of the wall meets the ceiling. Found in many historic homes, crown molding was originally made from plaster with molds and returned to the wall. Today, crown molding and other decorative elements traditionally made from plaster are made from wood, MDF (Medium-density fiberboard), or PVC (polyvinyl chloride). The benefits of using wood or synthetic materials is that they are much easier to work with and require fewer skills to install.

Chair Rails

Chair rails are a type of molding that is attached to the wall at chair height in dining rooms or eat in kitchens. The idea was to protect delicate plaster from being constantly bumped into by people pulling out chairs and hitting the wall. Chair rails are frequently installed along with wainscoting, decorative panels installed below the chair rails in order to protect the plaster wall.


An Architecture Cheat Sheet for Real Estate AgentsFormerly used as a type of exterior siding in cold climates, shiplap is now a trendy feature for country chic homes. What makes shiplap unique from ordinary boards nailed to the wall is that shiplap boards interlock together creating a tight and weatherproof seal that made shiplap ideal for colder climates before the advent of modern weatherproof siding.

Picture Frame Molding

An Architecture Cheat Sheet for Real Estate AgentsAnother decorative wall element common in turn of the century homes, picture frame molding is any molding used to create rectangular shapes that are reminiscent of picture frames on walls that already have crown and baseboard molding.

Baseboard Molding

An Architecture Cheat Sheet for Real Estate AgentsBaseboard molding is molding that is installed on the bottom of the wall where it meets the floor. Baseboard molding can be decorative, or serve to protect delicate plaster from kicks, moving furniture, or anything else that might hit the lower part of the wall.


An Architecture Cheat Sheet for Real Estate AgentsWainscoting is a decorative element often installed below chair rails that features large, rectangular panels made out of painted wood or plaster.

Ceiling Medallion

An Architecture Cheat Sheet for Real Estate AgentsOften used to accent a chandelier or lighting fixture, ceiling medallions are either painted wood, MDF, PVC, or plaster decorative elements that are installed on the ceiling. They can be purely decorative or used to hide wiring or support systems for chandeliers.

Types of Wood Flooring Common in American Homes

What’s beneath your client’s feet is also a very important interior design element to know about. After all, replacing doors is easy, windows more challenging, but replacing floors can be extremely expensive and will change the look of any home since flooring is usually at least one quarter of the visible space in any home. Here are a few common styles of wood and tile floors.


An Architecture Cheat Sheet for Real Estate AgentsParquet, French for “a small compartment,” is a style of wood floor that uses small pieces of wood cut into shapes that fit together to make larger patterns. The classic parquet is the interlocking squares version seen above. Herringbone and chevron are also common patterns used in parquet flooring.


An Architecture Cheat Sheet for Real Estate Agents

Without a doubt one of the most eye catching wood floor styles you’ll see as an agent, herringbone floors are made with small strips of wood installed in an interlocking “V” pattern on the floor. Herringbone floors have been used as a decorative element in homes since the 1500s, and continue to be a popular, if expensive, option for wood flooring today.


An Architecture Cheat Sheet for Real Estate AgentsChevron floors are a variation on herringbone parquet floors with a simpler, easier to install pattern that does not interlock. Instead, small strips of flooring are simply cut at matching angles and installed on the floor.


An Architecture Cheat Sheet for Real Estate AgentsInlays are purely decorative parquets that are often used to make border decorations or central medallions on high end wood floors. Due to the cost and expertise involved in installation, inlays are very rarely used today except in very high end homes. They are however somewhat common in turn of the century homes.


An Architecture Cheat Sheet for Real Estate AgentsLaminate flooring, also known by the earlier trademark “Pergo,” is a modern flooring product that uses layers of synthetic materials that have a wood grain pattern applied to them. They provide the look of hardwood floors, but for a fraction of the cost. Laminate flooring is also easier to install and maintain than hardwood flooring.


An Architecture Cheat Sheet for Real Estate AgentsHardwood flooring is made of thin or wide strips of actual hardwood like oak, walnut, hickory, maple, or cherry. These wooden strips generally also have a tongue and groove construction which allows them to be locked together for a tighter more water resistant seal. Note that the different varieties of hardwood species can be stained pretty much any color. Grain pattern is the best way to differentiate between species of wood used for flooring.


An Architecture Cheat Sheet for Real Estate AgentsCork flooring is a flooring product made from the bark of the cork oak tree. The bark is processed into sheets, and used as a flooring alternative to hardwood. Cork flooring is thought to be more environmentally friendly than hardwoods as the bark of cork trees can be harvested again and again.

Strip Flooring

An Architecture Cheat Sheet for Real Estate Agents

Strip flooring is made up of thin strips of wood, generally cut from less attractive areas of the tree including limbs and the upper portion of the trunk. If used in larger pieces, imperfections such as knots would be visible making the floor less uniform. Strip flooring can be made either from solid wood, or more commonly, thin strips of hardwood glued to other cheaper species of wood to save cost.

Wide Plank Flooring

An Architecture Cheat Sheet for Real Estate AgentsWide plank flooring on the other hand is flooring made up from large sections of the trunk of the tree. Imperfections such as knots are sometimes included in wide plank flooring. Since large sections of grain are visible and wide planks can only be cut from the most expensive parts of a tree, wide plank flooring is the most expensive hardwood flooring material there is. That said, wide planks are more common in 18th century homes as wood was less expensive.

Common Tile Flooring in American Homes

Natural Slate Tile

An Architecture Cheat Sheet for Real Estate AgentsOne of the most attractive and surprisingly affordable types of floor tile in American homes is natural slate, which is made up of large, sometimes rough sections of slate stone. Since slate stone can have natural imperfections, it provides a warm, natural look that is difficult to duplicate with synthetic materials. Slate tile is commonly found in entryways, basements, kitchens, and living rooms.

Terracotta Tile

An Architecture Cheat Sheet for Real Estate AgentsMore common in the Southwest, terracotta tile is a ceramic tile with a warm, reddish brown color that is also commonly used for roofing on Spanish style homes. Terracotta tile is commonly found in kitchens.

Over to You

What did you think of our list of common styles of homes, windows, doors, and flooring in the United States? Anything we missed? Have something you think we need to add to the article? Let us know in the comments!

The post An Agent’s Guide to Home Styles, Architecture, and Design appeared first on The Close.

This content was originally published here.

129 Union Street, Uniontown, PA 15401 | Uniontown Real Estate

Hardwood Flooring

Property Description

You’ll love to sit out front or in back of this big beauty in Uniontown! Covered front and back porches, fenced backyard, garage and pool are just a few features of this family and pet friendly home! Three bedrooms and the large 3rd floor is finished to turn into your 4th bedroom or as this family did, a game room! Hardwood flooring throughout, Gas Fireplace in the living room, New roof in 2017, new furnace and AC 2016, New electrical box 2015! There is a nice butlers pantry off the kitchen, which comes with full kitchen appliance package including a double convection oven, dishwasher and refrigerator. Downstairs is a nice drylocked basement with half bath, doors walk up to the back yard, this is a great set up for the pool with the half bath so close! Nice level easy care backyard which is fenced, an older garage is 2-car, has electric. Home Warranty Available, this one is not to be missed!

This content was originally published here.

1206 Sewickley Heights Dr, Aleppo, PA 15143 | Aleppo Real Estate

Hardwood Flooring

Property Description

Amazing townhouse with 2 master suites, 1 being on the main floor. All 3 bedrooms have en-suite bathrooms and large closets. This home is move in ready, updated and in excellent condition. Hardwood flooring throughout. Large entryway, living room with custom shutters and built-ins, large eat-in kitchen with a desk/work station, kitchen opens into large vaulted family room with a wood burning fireplace. Family room has custom built-ins and access to the deck with an automatic awning. The 1st floor master has access to the deck. Another master bedroom is on the second floor and has a large closet. The 3rd bedroom has a bathroom and large closet. There is a bonus space upstairs as well with built-in storage. This unit is a must see! Use of pool and tennis courts.

This content was originally published here.

Red Wing historic private homes offer rare inside looks | RiverTowns

Hardwood Flooring

The tour, which runs 1-4 p.m., is part of the Goodhue County Historical Society’s 150th anniversary celebration. Chairing the event is Lois Wipperling.

The sites, which can be visited in any order, are:

1121 East Ave., home of Charles and Lisbeth Butler;

818 W. Third St., the Candlelight Inn Victorian Bed & Breakfast, operated by David and Eve Baer;

1105 W. Fourth St., the Moondance Inn B&B, operated by Mike Waulk and Chris Brown Mahoney;

1166 Oak St., the Goodhue County History Center, formerly part of Red Wing’s early medical campus.

The houses all represent people who were instrumental in Red Wing’s early years and development, according to the historical society’s executive director, Robin Wipperling.

Tudor Revival

The Butler home is a Tudor Revival house built in 1938 by and for Dr. Brusegard. The Butlers purchased it from the Brusegard family in 1991 and bought additional land from a neighbor to expand the backyard.

Elements of the Tudor Revival style include graceful arches at the front entrance and some interior spaces along with a street-facing brick fireplace. Hardwood flooring is featured throughout the house.

Some interior remodeling has been done over the years, according to the Butlers. One of the downstairs bedrooms – there were four bedrooms originally – was eliminated to expand the living room. It appears that the house has been extended in both the back to enlarge the kitchen and in the front to create a room.

A highlight of the Butler home tour will be a visit to the large back yard, which Lisbeth Butler, an avid gardener, has filled with flowers and foliage. In the lower level visitors will get a look at interesting items the couple has collected while traveling.

She will be on hand during the tour to talk about the house and gardens.

Classical Revival

The Candlelight Inn dates to 1877, when it was built for Horace S. Rich, who was instrumental in establishing the clay industry in Red Wing. “Like a fine piece of pottery,” the Baers wrote in their blog, “the Candlelight was artfully crafted with supreme attention to detail.”

According to records for the West Residential Historic District, the three-story house is Italianate with a Classical Revival style porch added in the early 1900s. Original features include stained-glass windows, intricate butternut woodwork, and Quezal light fixtures.

The Baers moved to Red Wing in July 2018 and purchased the house, fulfilling a longtime dream. The elegant home, which had become a bed and breakfast inn in 1989, is filled with period antiques and modern amenities.

Tiffany and Steuben

The Moondance Inn, which has been operated by Waulk and Mahoney since 1999, was built in 1874 by Dr. A.B. Hawley. It has some 6,000 square feet of space on three floors plus a finished basement, plus a 1,200-square-foot carriage house that includes an owners’ apartment and a garage.

Spacious, with high ceilings and a sweeping walnut staircase, the house has exceptional woodwork, hardwood floors, the original gilded, stenciled ceiling and chandeliers with Tiffany and Steuben signed globes.

There are five bedrooms, a lobby with fireplace, an elevator, a third-floor space for retreats and meetings, an enormous pillared porch, and seasonal gardens that enable the Moondance to host both indoor and outdoor weddings.

The fourth site on the tour is the Goodhue County History Center, where special activities are planned for the afternoon. Staff will take people who have home tour tickets on behind-scenes tours of areas of the museum that are not open to the public.

Visitors also will have an opportunity to view “Celebrating the Society: 150 Years at GCHS.” The sesquicentennial exhibit spotlights 150 artifacts and images from the society’s collection that explore the stories of some of the county’s most interesting people, places and events.

Cookies and punch will be served at the museum. Anyone interested in opening their home for next year’s tour should leave contact information with staff.

Tickets to the home tour are $15. They can be purchased at the history center, online at www.goodhuecountyhistory.org, or by calling 651-388-6024. Tickets also will be available at the homes on the day of the tour only. Officials noted that the home tours are not designed to accommodate small children.

This content was originally published here.

4775 Robert Dr, Bethel Park, PA 15102 | Bethel Park Real Estate

Hardwood Flooring

Property Description

YOU WILL LOVE THIS MOVE IN READY RANCH HOME. Large living room with wall to wall carpeting and window treatments. Eat in Kitchen leads out onto a new rear deck. Exposed Hardwood flooring in two of the bedrooms. The insulated vinyl windows are newer with crosshatch muntins in some rooms. Trane furnace and A/C installed in 2009 still under parts warranty. New Roof in 2012 with shingle warranty. Newer hot water heater. New garage door and quiet opener. Updated bath in 2010 with walk in shower. This home is very clean throughout. The basement is spacious and features a shower and hookups for laundry with potential for an additional bath. Situated on a street with minimal traffic. Surrounding lawn comprises .43 acres.

This content was originally published here.

8420 David Drive, South Fayette, PA 15017 | South Fayette Real Estate

Hardwood Flooring

Property Description

MOVE RIGHT IN!!! CUL-DE-SAC street!! Spacious home with a great open floor plan!!! Two-story entry* Hardwood flooring* Deep crown molding* Dining room with tray ceiling* Cook’s CENTER ISLAND kitchen with CHERRY cabinetry, GRANITE counter tops, STAINLESS appliances, MORNING ROOM* Generous family room with STONE FIREPLACE* LUXURY owner’s suite offers TWO large walk-in closets, sitting room and private bath with his/her sinks, tile shower, tub* The ULTIMATE GAMEROOM features a stone WET BAR, BILLAIRD area, THEATER area, FITNESS area and FULL BATH* Rear yard PRIVACY with plenty of yard for pets and play* FIRST FLR LAUNDRY* Dual zone HVAC* Wtr Htr ’15* Walk-in attic access* Super-convenient location, minutes to I79, quick trip to Southpointe and downtown!

This content was originally published here.

83 Reese Rd, Buffalo Twp, PA 15301 | Buffalo Twp Real Estate

Hardwood Flooring

Property Description

Architectural delight! Open flowing floor plan-Living & Dining Rooms lined w/windows open to private wooded views, sunken living room w/vaulted ceiling and fireplace, Gorgeous Hardwood flooring & crown molding throughout, Generous size bedrooms and master retreat including luxurious en-suite. Gourmet Cherry Kitchen, ceramic floor, Granite counters, and Stainless Appliances! Kitchen opens to the maintenance free deck and adjoining “Spa” building. Easily convert into home business, work shop, or art studio-very flexible bonus space light and bright w ceramic flooring, high ceilings, and lined with windows. The Lower Level of the home is Huge & Finished-offers an additional bedroom or office, Family room w/fireplace, wet bar/kitchen area, laundry, bathroom, loads of storage &accesses the over sized garage! Private entrance and patio could be separate living area for today’s multi-generational families. Plenty of parking at the front door, making level entry a breeze. Unique/Custom Home!

This content was originally published here.

24 Hour Coffee Stain Test on Victoria Hardwood Flooring – South Cypress Blog

Hardwood Flooring

We tested the stain resistance of our Victoria hardwood flooring by letting coffee sit on it for 24 hours. We compressed it into a one minute video. After 1 hour, the coffee is easily whipped clean. At 2 hours, the process is just as easy without leaving a coffee stain. After 24 hours of we … Read more24 Hour Coffee Stain Test on Victoria Hardwood Flooring

This content was originally published here.

Weyerhaeuser Introduces Hardwood Edge OSB for Use Under Hardwood Floors

Hardwood Flooring

Federal Way, Wash., Feb. 6, 2013 – Hardwood Edge, new from Weyerhaeuser, is the industry’s first OSB floor panel specifically engineered for use under hardwood floors. The panels offer enhanced dimensional stability and high density that provide for outstanding fastener holding—ideal for the demands of hardwood floors. Hardwood Edge flooring is backed by a 65-year limited product warranty and a 365-day limited no-sand guarantee.

Hardwood flooring poses unique challenges for installers: The inherent swelling and shrinkage of wood as a natural material, improper acclimatization of hardwood, and insufficient drying time if the OSB is wet can work together to loosen fasteners, which can lead to pops and squeaks in a finished floor. Hardwood Edge panels are the result of multiple years of research by Weyerhaeuser, working closely with builders and flooring contractors, to create a product that is designed for use under all hardwood floors.

“Hardwood flooring is one of the most popular finishes for new homes, but it requires a stable, reliable subfloor that can withstand the high moisture conditions we have here in the Mid-Atlantic,” said David Walters, tactical product manager for Weyerhaeuser OSB. “Hardwood Edge flooring’s increased density and superior fastener-holding properties ensure hardwood flooring goes down easily and stays put, helping to reduce callbacks.”

Along with improved fastener-retention and high density, the panels include patented Down Pore® drainage technology: Three specially shaped grooves at panel ends that eliminate standing water to reduce the potential for water absorption. That built-in drainage, along with the panels’ proprietary edge seal, dramatically reduces edge swell, virtually eliminating the need to sand.

Available in a standard 4′ x 8′ panel size and 23/32″ thickness, Hardwood Edge panels are fully sanded and include a printed fastener template. The panels are designed to be installed consistent with the recommendations of the National Wood Flooring Association, including allowing the OSB to dry, allowing the hardwood flooring to acclimatize, and ensuring the difference in moisture content between OSB and flooring is within the range specified by the hardwood manufacturer.

Hardwood Edge flooring is initially available in the Mid-Atlantic region only.

For more information, visit .

This content was originally published here.

Choosing our Hardwood Flooring – Beneath My Heart

Hardwood Flooring

Welcome to Episode Two of our Notes from Home series!

(If you missed the tour of our new Tennessee home in the first episode, CLICK HERE to check it out!)

In today’s episode, Cy is going to start demo-ing the kitchen, while I begin to look at hardwood flooring options!

Picking out hardwood flooring for our home is a BIG decision, so I am so happy to be partnering with Twenty & Oak for this part of our renovation!

When we purchased our home, it had a very inexpensive laminate wood flooring in every single room that we knew we were going to have to replace.

We had a guy that wanted to come take up the flooring and buy it from us for a few hundred bucks, but the flooring was so cheap that it literally broke apart when taking it up.  Cy called the guy and told him not to come because the flooring was not worth trying to save.  Luke and Adam literally had the whole floor up in no time!

I was so excited that we were ripping up all the old laminate flooring and couldn’t wait to start looking for new hardwood flooring.  But before I did, I wanted to create a mood board that brought to life the look and feel that I wanted in our new home, specifically the kitchen and den.

As you can see, I want to incorporate a lot of black and white in our new home.  I love the clean, crisp feel that those colors create in a space.  But I also want to add warmth to our home with some wood tones in our kitchen cabinets, furniture, and definitely our hardwood flooring.

Since I knew that we would be needing new hardwood flooring throughout the home, I wanted something durable, kid friendly, and pet friendly.  BUT, I also wanted something beautiful and stylish.  

I found all of these things at Twenty & Oak. 

Twenty & Oak is an online resource for finding stylish, high quality flooring.  They are also connected to the best flooring retailers in the Southeast!  I was looking for engineered hardwood flooring for our home, but they also carry laminate, waterproof flooring, engineered stone, and luxury vinyl plank, tiles, and sheet.  They have something for every style and every budget!

When I went to the website, I browsed through all of the different brands that were available from Twenty & Oak.  This took some time, but boy was it fun!  I loved looking at all of the beautiful choices.  

As I was searching for my favorite stain colors, I noticed that I kept coming back to two different collections in the Palmetto Road brand… Tuscany and Chalmers.

What I LOVE about the Palmetto Road brand is that the hardwood flooring is crafted by hand!  Like REAL people with REAL hands, no machines.  They individually apply surface treatments like “wire brushed” or “hand scraped” by hand, which gives you a unique, authentic flooring.  It’s a custom look without the custom price!  LOVE THAT! 

In the Tuscany and Chalmers collections, I loved these hardwood flooring samples the most…

Since flooring can look differently online than in person, I couldn’t wait to order some samples of my favorite colors.  The cool thing is that at Twenty & Oak, you can always order three samples for FREE!  YAY!

But guess what?!!!!  

Since I am partnering with Twenty & Oak for this part of our renovation, that have created a special offer


How cool is that?!

You guys will be able to CLICK HERE and check out all of the beautiful flooring options at Twenty & Oak, and they will ship you SIX FLOORING SAMPLES for free!

That’s awesome!

I am SO GLAD I ordered free samples of my favorite hardwood flooring because some of them looked different that I expected.  Seeing and touching the flooring in person made a huge difference in my decision.

Here are two of my favorites…

BISCUIT (left) &  NOLA (right)

To help me make my decision though, I wanted to see a larger sample of my hardwood flooring choices.  I knew I could do that by visiting one of Twenty & Oak’s retailers.  I put my zip code in the store locator box on their site and found three retailers in my area. 

You can do the same thing too!  Just CLICK HERE to find a Twenty & Oak retailer near you. 

I will be visiting the retailer I chose and sharing all of the details in a future episode of Notes from Home, so stay tuned!!!

Now are you ready for this week’s episode?!

I have to give major props to my son, Luke, for helping me create this video series!  I COULD NOT do it without him!

I hope you enjoy watching this episode, and be sure to head over to Twenty & Oak when you are finished watching and order some FREE flooring samples for your next project!

*This post is sponsored by Twenty and Oak.  All opinions and ideas are 100% mine!

Success! Now check your email to confirm your subscription.

There was an error submitting your subscription. Please try again.

This content was originally published here.