How to Build an Outdoor Living Room – Feedster
There’s nothing quite like kicking back on your own Patio—until the sun starts cooking you or the rain begins to fall. But you can easily double your time in the great outdoors with this beautiful pavilion. Just think—no more rainouts during your next barbecue! And with a roof, you can relax on dry, clean, comfortable, padded furniture, which just can’t stand up to the elements on an open patio. All in all, you can give your patio the feel and function of an outdoor living room. But the best part is, this pavilion will add real beauty and value to your home by dressing up that lonely, underused space.
While this outdoor living room design may look complicated to the novice carpenter, don’t be intimidated. If you have the basic hand power tools, can handle a circular saw and have a bit of remodeling experience, you have the moxie to pull off this project. We’ll show you some scribe-it, nail-it-up and cut-it-in-place techniques that greatly simplify the tough spots and speed up the project. In fact, another carpenter and I built the basic structure in three leisurely days and spent a fourth day finishing the decorative column skirts. Give yourself and a helper about twice as long and you may finish faster than you think.
Besides a carpenter’s apron outfitted with the basic hand tools, all you need are a 4-ft. level, a circular saw, a jigsaw and posthole digging tools. But consider renting a power nailer for a day to save time and effort for the massive job of nailing down the roof decking.
Comparing the before and after photos, you can see that in addition to building the pavilion, we did some major stonework and planting. Those improvements aside, our total materials bill was roughly $4,000.
Note: A complete Materials List is available as a pdf in Additional Information below.
Figure A: Roof Assembly
This front view shows the basics of the patio roof. Make a scale drawing of the structure adapted to your own house before applying for a building permit.
Figure A is also available as a pdf in Additional Information below.
Sandwich framing and 2×6 tongue-and-groove decking construction
The design of this roof resembles traditional post-and-beam construction, but without the headaches of working with heavy, expensive timber and the tricky joinery that goes with it. The posts, beams, rafters and ceiling ties (see Figs. A and B) are built-in-place sandwiches of common 2×4, 2×6, 2×8 and 2×10 smooth cedar lumber. The center board of each sandwich is 2 in. narrower than the outer ones, which lends attractive shadow lines and architectural “heft” to the building.
This triple-thick assembly method makes the framing members very strong, which allows for longer spans and wider spacing between members. This technique allows you to overlap and lock all the pieces together for a very strong framework, easier nailing and tighter joints. And, by assembling beams in layers, they’re lighter to lift. Since the rafters are so beefy, you can space them 32 in. apart. But those wide spans call for a roof decking that can handle those spans. Tongue-and-groove 2×6 decking (Photo 18) fills the bill nicely because it’s very strong, reasonably priced and easy to install. It also looks great on the inside. You can let butt ends of the roof decking fall randomly throughout the roof; it’s not important that they splice over framing members. But the seams will look more polished if you use a block plane to carve a little chamfer on decking ends where two boards meet.
Figure B: Pilaster Assembly
The pilaster assembly is designed to float around the piers, allowing for movement due to freezing and thawing.
The cedar base trim will last longer and look better over time if you hold it an inch or so above patios to keep the wood dry.
Figure B is also available as a pdf in Additional Information below.
This flexible design is easy to customize
Photo 1: Lay out the footprint
Assemble a rectangular template to mark the outer perimeter of the posts and beams. Use the dimensions from your plan and tack together 2x6s and a 2×8 ridge board. Square the template using the 6-8-10 squaring method shown. Nail 2x4s across the corners to keep the template square.
Photo 2: Lay out the roof
Mock up the roof framing against the wall. Cut three 4-1/2- x 9-1/4-in. plywood rectangles to simulate the beams and ridge and use 2×6 rafter stock to lay out the rafters. Position the beam templates by drawing vertical lines on the siding with a 4-ft. level and a straight 2×4, using the perimeter template as a guide (Photo 1). Measure halfway between the templates and draw a vertical line to mark the center of the roof. Tack each 2×6 rafter to the siding with a couple of 16d nails crossing at the centerline. Tack the ridge template at the point where the rafters cross, keeping the top two corners even with the rafter tops.
Photo 3: Dig footings
Dig 12-in. diameter footing holes to frost depth and pour 6-in. concrete footings in the bottom (Fig. B). Then reposition the perimeter template precisely and recheck squareness. Nail the lower post assemblies together with 16d hot-dipped galvanized nails spaced every 4 in. Drop them onto the concrete footings. Then plumb and brace the posts in both directions and backfill the holes, packing the soil every few inches.
Toenail the assemblies to the template corners.
We give the basic measurements for the structure in Fig. A, but don’t treat them as a cutting list, because you’ll most likely have to adjust them to fit your own home. Adjusting sizes is easy. First you get the beams and posts laid out and in position, then you simply measure or scribe the rest of the elements for exact lengths or angles before cutting them to length and installing the parts. On your site, you may need to widen or deepen the structure to miss windows or doors on the house or bridge over existing patios.
You can “grow” the length or width of the roof as much as 2 ft. without compromising structural integrity and shrink it as much as you want. The roof lines can also be altered to miss wall obstructions. We had to steepen the roof slope on one side to miss the bay window you see in Photo 2. Under that window, the roof has a 7/12 slope (7 in. of vertical drop for every 12 in. of horizontal distance), while the other side has a 6/12 slope. At a minimum, you should try to have a 4/12 slope if you live in a snowy area. Ask your building inspector for minimum slopes for your area when you pick up the building permit. But remember that steeper pitches may call for longer rafters and more decking. You can figure out required material lengths when you go through the layout exercise we show in Photos 1 and 2.
The easy way to determine the shape and slope of your roof is to first lay out the “footprint” of the posts and beams using the dimensions we give you (Photo 1). Then use a 4-ft. level and a straight board to draw the beam locations on the walls. The height of the bottom of the beams should be at least 6 ft. 8 in. for “headbanging” clearance (Photo 2). Tack 4-1/2 x 9-1/4 in. beam templates cut from plywood to the wall to simulate beams. Then lay out the roof lines with two 2x6s tacked through the siding to be sure:
The rafter tails have a minimum of 6 ft. 8 in. of head clearance.
The roof has at least a 4/12 slope.
The windows, bays or other wall projections are spaced at least 5 in. above the rafters to leave room for flashing.
This is the time to make final adjustments to the roof slope and the post-and-beam locations. If everything seems OK, you can start digging your footings (Photo 3).
Foundation-grade posts and floating base skirts
Photo 4: Add the slip forms
Cut and assemble two lower and upper slip forms (used for post trim later; Fig. B), then slip them over the posts and let them rest on the patio.
Photo 5: Cut slots for the flashing and rafters
Trace around the beam templates and the bottom of the ridge templates (Photo 2) and pull them free. Mark the tops and ends of the rafters and remove them. Snap chalk lines 3 in. above the rafters to allow space for the decking and step flashing (Photo 20). Set the circular saw to cut just through the thickest part of the siding and cut out the 3-in. wide strip, leaving the sheathing intact.
Photo 6: Cut in the ledger
Snap chalk lines between the tops and bottoms of the two beams and cut the ledger recess through the siding and sheathing. Cut one end of a 10-ft. 2×10 ledger to match the roof angle, hold it in place, and mark and cut it at the center point. Nail the ledger in place with two 16d galvanized casing nails into each wall stud, except for the studs on each side of the joist hanger position. Repeat for the other ledger half.
Photo 7: Fasten the ledger
Bolt the ledger into the studs on each side of each joist hanger location with three evenly spaced 1/2 x 5-in. lag screws with washers. Nail triple 2×10 joist hangers to the ledger at each beam location with 1-1/2 in. galvanized joist hanger nails, then screw through the large hanger holes with 1/2 x 2-in. lag screws. (First drill 3/8-in. pilot holes for all lag screws.)
Photo 8: Level and mark the beams
Extend the posts with 2×4 and 2×6 cedar so that they project beyond the top of the ledger, nailing every 4 in. with 16d casing nails up to the beam height. Cut a 2×10 beam member to length and shape the end. Rest it in the joist hanger, level it and mark the height on the post. Cut only the post 2x6s at that height with your circular saw. Cut the center 2×4 9 in. higher (Fig. A).
Use .60 foundation-grade treated 2x4s and 2x6s for the lower post sections and the footings (Fig. B). You may have to special-order them, but the added longevity is worth the money and trouble. For the above-ground base skirt framing and sheathing, standard .40 treated material will work just fine.
The base skirts are designed to “float,” that is, slide up and down the fixed posts that they encase. That’s especially important when they rest on a slab or stone surface in cold regions where frost can lift patios when the ground freezes. The skirts can move up and down during freeze/thaw cycles, but the posts, which extend below frost depth, stay put—without lifting the entire structure. So when you frame and trim the pilaster base skirts, make sure everything fits loosely.
If the posts have to penetrate a concrete or stone surface, cut a 20- in. square hole for digging the footings (Photo 3). Use a circular saw with a diamond blade and don’t worry about making it pretty; the skirt will cover the hole. To prevent settling, just be sure to pack the soil well as you backfill around the posts.
Bracing as you build
Photo 9: Add the ridge beam
Nail the outer 2×10 beams into the post’s center 2×4 with three 10d galvanized box nails and into the joist hanger with 1-1/2-in. joist hanger nails. Plumb and brace the posts as shown. Center and nail the two temporary ridge supports, one to the house and the other to the post braces. Cut, place and tack each ridge member in position atop the ridge supports, then recheck the ridge for level and center. Brace the ridge with a couple of 2x4s nailed to the ridge and each beam. Nail the ridge members together from both sides with 10d galvanized box nails.
Photo 10: Scribe the rafters
Cut an approximate 25-degree angle on the first 2×6 rafter and hold it in place against the ridge. Use a 2×4 to scribe the exact angle on the rafter. Use the rafter as a pattern to cut all the 2×6 rafters for that side. Repeat the process on the other side of the ridge.
Photo 11: Attach rafters
Lay out the rafter positions on the beams and ridge as shown in Fig. A and toenail the rafters into the ridge with three 16d galvanized nails (where they’ll be hidden by the middle board of the “sandwich”). Sight down the beams to make sure they’re straight before installing the rafters. Straighten if necessary and hold them in place with braces until the rafters are on. Nail hurricane tie-down straps to the middle side of the rafters and to the inside of the beams with 1-1/2-in. galvanized joist hanger nails.
Photo 12: Construct the beams
Center and nail the two-piece middle 2×8 beam members to the 2x10s with alternating 10d nails spaced every 8 in. Then nail up the inner 2x10s with the same nailing pattern.
Photo 13: Cut the ceiling ties
Push the 2×6 ceiling ties against the rafters and scribe the end cuts to match the underside of the rafters. Number them to avoid confusion. Cut a second 2×6 ceiling tie for each rafter using the ones you scribed as patterns for their mates. Tack one under each rafter with a 10d toenail and save their mates for the other side of the sandwich later.
Photo 14: Add rafter ties and rafter boards
Cut the middle 2×4 rafter tie boards so they’re flush with the outside of the beams. Nail them to the rafters and the 2×6 ceiling ties with 10d nails spaced every 12 in. along each edge. Cut the 2×4 rafter center boards as shown here and in Fig. A and nail them to the center of the 2×6 rafters. Cut the center 2×4 rafter tails so they’re just short of the horizontal level cut.
Photo 15: Cut the curved braces
Cut two 4-ft. lengths of 2×10 and tack them between the 2×4 rafter and ceiling tie parts to lay out the curved decorative braces (our positions vary because of the differing roof slopes). Mark the lengths at the 2x4s. Bend and clamp a thin board and trace arcs about 7-1/2 in. apart on both sides. Cut them with a circular saw and jigsaw and nail them into place.
Photo 16: Complete the rafters and ceiling ties
Nail on the previously cut 2×6 rafters and 2×6 ceiling ties to the 2x4s to complete the rafter and tie sandwiches. Place 10d casing nails every 12 in. Toenail the rafters to the ridge beam.
Photo 17: Cut the rafter ends
Transfer the rafter tail length from the house rafter to the outermost rafter and snap a chalk line to that mark. Draw the 1-in. end cut with a square and the level cut on both sides of each rafter using a 2- or 4-ft. level. Make the rafter tail square cuts first with the circular saw, then make the horizontal level cuts.
Mark the rafter tails with a chalk line.
We show a fail-safe method of positioning your outdoor living room posts so they’re square and spaced perfectly from the house and each other. The trick is to use a jig made from the framing materials (called a “footprint template” in Photo 1). Initially tack the posts to the jig (Photo 3, inset) and then later to each other (Photo 9). Constantly check the posts throughout the construction to keep everything square and plumb and you’ll make your life easier as you assemble the upper parts.
The ridge assembly is especially tricky to center and support before the rafters are in place. Use the rafter mockup (Photo 2) to determine the height of the bottom of the ridge and tack a temporary 2×6 support against the house to support that end of the ridge (Photo 9). The temporary brace that supports the yard end of the ridge will most likely be taller to accommodate any drainage slope on the patio. Cut that support a few inches longer, tack it in place and use a long, straight board and level from the top of the house-mounted support to mark the length. Then cut it to length and use existing and additional supports to hold it in place before you set the ridge. A couple of 2x4s nailed to the outside and a couple of braces will keep the ridge from slipping off the support while you’re installing the rafters. We assembled the ridge sandwich on the ground and lifted it into place, but it was a struggle for the two of us! It’d be much easier to lift the boards separately and nail them together once they’re up.
After the ridge is assembled, measure from the ridge edges to the beams on each wall. To center the ridge perfectly, adjust the ridge until the right and left measurements are the same. Note that if you have to build an offset roof as we did, the ridge will no longer be exactly centered, but you still have to make it parallel to the beams.
Photo 18: Deck the roof
Lay the first course of tongue-and-groove roof decking with the groove side facing downhill flush with the rafter ends. Nail the roof decking into one rafter of each rafter pair with two 10d nails. Select lengths so butt seams fall randomly throughout the ceiling. Halfway to the peak, check to make sure the boards are running parallel to the ridge beam. If they’re not, adjust the next few courses slightly to fix the problem.
Snap a chalk line flush with the edge of the fascia board and cut off the decking ends with a circular saw.
Photo 19: Add the shingle molding
Nail the shingle molding onto the eave edge flush with the top of the decking with 7d nails into the rafters and the decking. Notch the gable-end shingle molding around the ridge and nail it to the fascia. Cut the end of the gable shingle molding flush with the eave molding with a handsaw.
Photo 20: Step flashing
Staple roofing felt onto the decking and shingle the roof following the manufacturer’s instructions on the wrappers. Bend and tuck 5 x 7-in. shingle tins under the siding and over the top half of each shingle for every course against the house. It’s easiest to slide the step flashing up from the bottom edge of the last piece of siding.
Photo 21: Build the pilasters
Cut and assemble the tapered plywood post-base sides using Fig. B as a guide. Raise the top slip frame 5 ft. above the floor and hold it in place with a 2×4 block toenailed into the post. Nail the side pieces to the top and bottom slip frames and to the 2x2s with 7d galvanized nails spaced every 6 in.
Photo 22: Shingle
Shingle the pilasters by alternating overlaps at each course and corner. Using a pencil, lightly draw level lines about 8 in. up from the bottom of the course below for straight shingle guidelines. Hold each shingle plumb and scribe angles on the backside of the shingle.
Whichever wood types you decide on, think ahead and prefinish the wood whenever possible—especially if the roof decking sports a different finish than the framing. We put two coats of exterior latex stain on the decking before installing it. That saved tons of time over painstakingly cutting in cleanly around the framing. For the same reason, it pays to apply an exterior sealer on the cedar after the structure is up and before installing the decking. If you’re staining or painting standard framing lumber, we suggest applying the finish before erecting the structure and then touching up nail holes and end cuts after construction. You’ll get a better, faster paint job and the wood surfaces that are buried inside sandwiches will be better protected from moisture in your outdoor living room.
Selecting the Wood
We used smooth dimensional cedar for all of the exposed framing for this pavilion. However, we decided on stained spruce tongue-and-groove 2x6s for the roof decking because cedar decking cost nearly twice as much. You can save about even more by using standard framing material for the entire structure—a smart move if you intend to paint or stain everything to match the house.
Even though the structural elements are exposed, you don’t need flawless lumber for your pavilion for a clean, handsome look. Simply select the lumber with the best faces for the edges and sides that will show in your outdoor living room. We had all the lumber delivered (in other words, we just got random picks from the lumberyard) and had no problem finding enough good-looking sides and edges. If you’re dissatisfied with the look of any of the lumber, you can always exchange it.
Required Tools for this Outdoor Living Room Project
Have the necessary tools for this DIY outdoor living room project lined up before you start—you’ll save time and frustration. Air compressorAir hoseBelt sanderBrad nail gunChalk lineCircular sawCordless drillDrill bit setFraming squareHammerHandsawJigsawLevelMiter sawPaintbrushPosthole diggerSafety glassesSocket/ratchet setSpeed squareWheelbarrow
Read more: familyhandyman.com
Will is the Executive Managing Editor at Feedster. Will and his team from Full Epic Lead Generation work with venture capital, marketing co-ops, and companies to attract and gain qualified leads.
His primary focus on developing a sales funnel for a company and finding out of the box / growth hacking style ways to convert and drive traffic.
This content was originally published here.